manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual, Page: 350 / 436

Share
Download
Cisco WS-C3550-12G User Manual Download Page 350

 

10-42

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 10      Virtual Interface Management

Loopback Interface Management Window

The following tabs are available on the Loopback Interface Management window:

•

Configuration Tab

•

Additional Notes Tab

Configuration Tab

The Configuration tab of the Loopback Interface Management window consists of a single area, 
Configuration. The Configuration area provides the following information:

•

Loopback Interface Table—Lists the loopback interfaces that have been deployed on the device. The 
unique identifier of a Loopback interface in the device is displayed in this table:

•

Description—Description of the interface corresponding to the index selected in the Loopback 
Interface Table.

The following subareas are available within the Loopback area on the Configuration tab of the Loopback 
Interface Management window:

•

Layer 3 

•

Routing Protocol 

•

Loopback 

Layer 3 

The Layer 3 subarea provides the following information:

•

IP Address—IP address of the interface. A value of 0.0.0.0 indicates that no IP address has been 
configured on the interface.

•

Netmask—IP subnet mask of the interface. The value of the mask is an IP address with all the 
network bits set to 1 and all the host bits set to 0.

Routing Protocol 

The Routing Protocol subarea contains the following information:

•

ISIS Area Tag—Identifies the IS-IS routing area that the Loopback participates in. If multi-area 
IS-IS is configured on the device, the IS-IS area must be named. Otherwise, this value may be an 
implicit null tag. This attribute is only valid if the IS-IS Enabled attribute is true (1).

•

ISIS Enabled—Indicates whether or not IS-IS routing is enabled on the interface. IS-IS routing can 
only be enabled if the loopback interface has been assigned an IP address.

Loopback 

The Loopback subarea contains the following information:

•

Loopback Index—Unique identifier of a new loopback interface to be deployed on the device.

•

Create—Deploys on the managed device a loopback interface identified by the Loopback Index 
field. The newly added loopback interface will be displayed in the Loopback Interface Table.

•

Remove—Removes the loopback interface identified by the Loopback Index field from the device.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments