Cisco WS-C3550-12G User Manual Download Page 230 | Manualshive

Page: 230 / 436

background image

8-84

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8 Interface and Subinterface Management

ATM/E3 Interface Management Window

The following tabs are available on the ATM/E3 Interface Management window:

•

Status Tab

•

Configuration Tab

•

ATM/E3 Tab

•

Performance Tab

•

Routing Protocol Tab

•

Additional Notes Tab

Status Tab

The following areas are available on the Status tab of the ATM/E3 Interface Management window:

•

Interface Status

•

Performance Logging

Interface Status

The Status area provides the following information to describe the general characteristics of the
interface:

•

Description—Comment or a description to help you remember what is attached to this interface. The
description is only put in the configuration to help you remember what specific interfaces are used
for.

•

Index—String index of the interface. This attribute is read-only.

•

Operational Status—The current operational state of the interface. This attribute is read-only. This
attribute has one of the following values:

–

testing—Indicates that no operational packets can be passed.

–

unknown

–

down

–

up

–

dormant—Interface is waiting for external actions (such as a serial line waiting for an incoming
connection)

–

notPresent—Interface has missing (typically, hardware) components.

–

lowerLayerDown—The interface in the lower layer is down.

•

Administrative Status—The desired state of the interface. This attribute has one of the following
values:

–

testing (read-only)—Indicates that no operational packets can be passed.

–

up

–

down

•

Last Change—The value (in seconds) of sysUpTime at the time the interface entered its current
operational state. If the current state was entered prior to the last reinitialization of the local network
management subsystem, then this object contains a zero value. This attribute is read-only.

«
...
228
229
230
231
232
...
»

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WS-C3550-12G

Brand: Majesti-Fi Pages: 2

Brand: D-Link Pages: 3

Brand: Abocom Pages: 14

Brand: Cambium Networks Pages: 3

Brand: Cambium Networks Pages: 68

MSR900-E Routers

Brand: H3C Pages: 38

Brand: H3C Pages: 64

Brand: H3C Pages: 34

Brand: TP-Link Pages: 2

RUCKUS ZoneDirector 1200

Brand: Arris Pages: 2

Brand: Sunix Pages: 41

Brand: H3C Pages: 33

Brand: EliteConnect Pages: 214

Brand: WoMaster Pages: 115

Brand: Ebyte Pages: 10

Brand: D-Link Pages: 64

Brand: D-Link Pages: 3

Brand: D-Link Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands