manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 207

 

8-61

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

ATM/SONET Interface Management Window

ATM/SONET Interface Management Window

The ATM/SONET Interface Management window describes a physical and logical enhanced ATM OC-3 
interface of a FlexWAN port adapter on the Catalyst switch. This window can be launched from the ATM 
Port Adapter or ATM SONET interface object within the Physical view.

To launch the ATM/SONET Interface Management window, perform one of the following:

•

Right–click a Network Element object within the Network or Physical containment views, then 
choose CSM/7600 Manager > Physical > Interface > ATM/SONET.

•

Right–click a Chassis object within the Network or Physical containment views, then choose 
Physical > Interface > ATM/SONET.

The following figure is an example of the ATM/SONET Interface Management window.

Figure 8-18 ATM/SONET Interface Management Window

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands