manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 378

 

11-26

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 11      Routing Management

BGP Management Window

Troubleshooting Command

The Troubleshooting Command area describes the BGP area configurations:

•

Command—Indicates the selected troubleshooting command. Possible values are:

–

Display cidr Only

–

Display Inconsistent Autonomous

–

Display Paths

–

Display Summary

–

BGP <prefix>

–

BGP Community <community-number> Exact

–

BGP Community List <community-list-number> Exact

–

BGP Filter List <access-list-number>

–

BGP Regular Exp <regexp>

–

BGP <network> <network-mask>

–

BGP Neighbors <neighborId>

–

BGP Neighbors <neighborId> received-routes

–

BGP Neighbors <neighborId> routes

–

BGP Neighbors <neighborId> advertised-routes

–

BGP Neighbors <neighborId> paths

–

BGP Neighbors <neighborId> dampened-routes

–

BGP Peer Group <tag> Summary

•

Command Table—Presents data according to the Command list selection.

•

Access List—Displays the applicable access list entries according to the option selected from the 
Command list.

•

Community List—Displays the applicable community list entries according to the option selected 
from the Command list.

The following fields may be edited as necessary depending on the selected troubleshooting 
command.

–

Access List Number

–

Network Mask

–

Regular Exp

–

Neighbor IP

–

Prefix

–

Community List Number

–

Community Number

–

Network

–

Peer Group Tag

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands