manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 134

 

7-22

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 7      Module and Port Adapter Management

SLB Module Management Window

Client Side VLAN Tab

The following areas are available on the Client Side VLAN tab of the SLB Module Management 
window:

•

Client-Side VLAN 

•

Client VLAN Config 

Client–Side VLAN 

The Client Side VLAN area provides the following information:

•

Client–Side VLAN Table—Identifies the client VLANs used by the CSM. These are the VLANs on 
the device to which clients will connect. The following attributes are displayed for the selected client 
VLANs in the table:

–

IP Address—IP address of the client VLAN.

–

Netmask—Subnet mask of the client VLAN IP address. Enabled bits indicate network 
addressing bits in the IP address.

•

Client–Side VLAN Gateway Table—Describes the default gateways associated with the client 
VLANs. There may be multiple gateways associated with each client VLAN. The following 
columns are displayed in this table:

–

Client Side VLAN—Unique identifier of a client VLAN on the device.

–

Gateway—Default gateway of a client VLAN. A router to the client VLAN must have this 
gateway address configured and real servers must point their gateways to this address.

Client VLAN Config 

The Client VLAN Config area allows the user to add client side VLANs. The following attributes are 
configured:

•

Client Side VLAN—Unique identifier of a client VLAN on the device.

Note

VLAN 1 is the default VLAN. VLAN identifiers greater than 1001 are reserved as the default 
VLANs for various media and for hidden VLANs generated by the device.

•

Client VLAN Add—Adds the client VLAN specified in the client side VLAN field. If you do not 
specify a VLAN in the Client Side VLAN field, no action will take effect.

•

Client VLAN Remove—Removes the client VLAN that is selected in the Client VLAN Table. A 
dialog box appears, asking you to confirm the action.

Gateway Config 

The Gateway Config subarea allows the user to add a default gateways associated with the client VLAN 
specified in the Client Side VLAN field. This VLAN must already be configured as a client side VLAN.

•

Gateway—Default gateway associated with the client VLAN.

•

Gateway Remove—Removes the default gateway specified by the Gateway field and the Client Side 
VLAN field. You need to specify a VLAN in the Client Side VLAN field and an IP address in the 
Gateway field for the action to take effect.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands