manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 432

 

13-34

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 13      Alarms and Alarm Management

Cisco Catalyst Switch Manager Alarms

Modules/Port Adapters

The following table describes the Module object attribute alarms.

Port adapters do not support the operational status information, as a result the only attribute alarm raised 
by a port adapter is the final one - a serial number change has been detected.

Table 13-12  Module Attribute Alarms

Attribute

Description

Severity

Alarms Cleared

Operational 
Status = ok

“C6576M Module Operational Status is 
ok”

Normal

Operational Status = 
other
Operational Status = 
minorFault
Operational Status = 
majorFault

Operational 
Status = other

“C6576M Module Operational Status is 
other”

Minor

Operational Status = 
minorFault
Operational Status = 
majorFault

Operational 
Status = 
minorFault

“C6576M Module Operational Status is 
minorFault.”

Major

Operational Status = 
other
Operational Status = 
majorFault

Operational 
Status = 
majorFault

“C6576M Module Operational Status is 
majorFault.”

Critical

Operational Status = 
other
Operational Status = 
minorFault

Serial Number

“C6576M Module Serial Number has 
changed. The Module has been replaced 
with a different card of the same type.”

A change in this value indicates that the 
Supervisor module was removed and 
replaced with another of the same time.

Critical

None

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands