Cisco WS-C3550-12G User Manual Download Page 380

Page: 380 / 436

11-28

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 11 Routing Management

BGP Management Window

Figure 11-11 BGP Management—Configure Peer Window

The following is displayed on the BGP Management—Configure Peer window:

–

Local AS—Indicates the BGP autonomous system number enabled.

–

Neighbor IP Address—IP address of the local network to be added to or removed from the BGP
process.

–

Neighbor Remote AS—Mask to be used with the neighbor IP address.

–

Add Neighbor Entry—Adds the neighboring router identified to the selected BGP process.

–

Remove Neighbor Entry—Removes the neighboring router identified from the selected BGP
process.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Search results

Summary of Contents for WS-C3550-12G

Reviews:

Related manuals for WS-C3550-12G

Brands by name

Popular brands

Cisco WS-C3550-12G, User Manual

Search results

Summary of Contents for WS-C3550-12G

Reviews:

Related manuals for WS-C3550-12G

Brands by name

Popular brands