manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual, Page: 329 / 436

Share
Download
Cisco WS-C3550-12G User Manual Download Page 329

 

10-21

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 10      Virtual Interface Management

VLAN Management Window

–

Failed—The backup operation failed.

–

Not executed—A backup has not been executed.

•

Backup File—Name of the file on the TFTP server to which the VLAN configuration will be copied 
to.

•

Save config file before reset— “true” indicates that the VLAN configuration file will be saved 
before switch reset.

•

Restore Status—Status of the last VLAN configuration restore operation. The Restore Status has the 
following values:

–

Ok—The restore operation completed without errors.

–

Failed—The restore operation failed.

–

Not executed—A restore has not been executed.

•

Restore File—Name of the file on the TFTP server to which the VLAN configuration will be 
restored from.

•

Backup—Backs up the VLAN configuration to the file specified in the Backup File field on the 
TFTP Host. 

•

Restore—Restores a VLAN configuration backup or loads a new VLAN configuration. Copies the 
file specified by the Restore File field from the TFTP Host to the switch or router.

Caution

The Restore and Schedule Restore buttons will cause the switch to be reset after the VLAN database 
restoration process is complete.

•

Schedule Restore—Schedules the restore operation. Launches the Schedule dialog box consisting 
of the following:

–

Date—The date when the backup will start. The format is MM/DD/YYYY.

–

Hour—The hour when the backup will start. It is a 24-hour clock.

–

Minute—The minute when the backup will start.

Note

An alarm is generated if the Backup Status and Restore Status attributes are set to Failed.

Note

VLAN Database Backup/Restore is not supported in VTP Client/Transparent mode as of IOS 
12.1(8a)EX and later.

Additional Notes Tab

The Additional Notes tab of the VLAN Management window contains the Notes area which is a text box 
that allows you to type in additional notes.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments