manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 75

 

4-15

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 4      Deploying the Cisco Catalyst Switch Manager

Predeploying Anticipated Network Objects

Predeploying Anticipated Network Objects

The predeployment option is used to deploy a Catalyst switch into Cisco EMF before it has been attached 
to the network. After an object has been predeployed, Cisco EMF keeps the object in a decommissioned 
state until the device corresponding to the object is added to the network. After the switch is brought 
on-line, the predeployed object can be configured to automatically commission. The following objects 
can be predeployed:

•

Network Element, Software and Chassis

•

Supervisor Modules

•

Ethernet Modules

•

Switch Fabric Modules

•

FlexWAN Modules

•

Port Adapter

•

Content Switching Module

•

EtherChannel Modules

The remaining Cisco Catalyst Switch Manager objects are automatically discovered when you 
commission the Network Element object.

Predeploying Network Element, Software, and Chassis Objects

To manually predeploy the Network Element, Software, and Chassis Cisco Catalyst Switch Manager 
objects from various objects within the object hierarchy, proceed as follows. 

If deploying from a generic Site container object, perform the following steps:

Step 1

Right-click a generic Site container object, then choose Deployment > CSM/7600 Manager, then 
choose one of the following options:

–

Deploy Catalyst 6000 Chassis

–

Deploy Catalyst 6500 Chassis

–

Deploy Cisco 2950 Chassis

–

Deploy Cisco 2970 Chassis

–

Deploy Cisco 3550 Chassis

–

Deploy Cisco 4000 Chassis

–

Deploy Cisco 4500 Chassis

The Deployment Wizard appears, displaying the Deployment Wizard—Templates window.

Depending on the Catalyst switch family selected in 

Step 1

, the Deployment Wizard—Templates 

window displays different options. The following deployment templates display in the Deployment 
Wizard—Templates window when the Catalyst 6000 or 6500 chassis deployment option is selected:

•

Network Element with IOS installed (Auto–discover Chassis)

•

Network Element with IOS installed (Specific Chassis)

•

Network Element with IOS/CatOS installed (Auto–discover Chassis)

•

Network Element with IOS/CatOS installed (Specific Chassis)

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands