manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 54

 

3-2

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 3      Getting Started

Preparing to Use the Cisco Catalyst Switch Manager Software

Preparing to Use the Cisco Catalyst Switch Manager Software

The following procedure outlines the general steps involved in using the Cisco Catalyst Switch Manager 
software.

Step 1

Install and start Cisco EMF.

Note

For more information on how to install and start Cisco EMF, see the Cisco Element Management 
Framework Installation and Administration Guide.

Step 2

Install the Cisco Catalyst Switch Manager software.

Note

For more information on how to install the Cisco Catalyst Switch Manager, see the Cisco 
Catalyst Switch Manager Installation Guide.

Step 3

Set up the Catalyst switch.

You must configure the Catalyst switch to support SNMP management before it can be properly 
managed by Cisco EMF.

Note

For more information on configuring the switch, see the “Software Configuration 
Requirements” section in the Cisco Catalyst Switch Manager Installation Guide.

Step 4

Start a Cisco EMF session.

Starting a Cisco EMF user session provides access to all Cisco Catalyst Switch Manager functionality. 
For more information, see the 

“Launching Cisco EMF” section on page 3-3

.

Step 5

Deploy objects.

For more information, see the appropriate deployment section in 

Chapter 4, “Deploying the Cisco 

Catalyst Switch Manager.”

Step 6

Configure and monitor managed objects using object management windows as necessary.

For more information, see the 

“Working With Object Management Windows”

 section in 

Chapter 4, 

“Deploying the Cisco Catalyst Switch Manager.”

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands