Cisco WS-C3550-12G User Manual Download Page 215

Page: 215 / 436

8-69

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8 Interface and Subinterface Management

ATM/SONET Interface Management Window

•

Severely Err Secs—Number of severely errored seconds encountered by the SONET Line in the
current 15-minute interval.

•

Coding Violations—Number of coding violations encountered by the SONET Line in the current
15-minute interval.

•

Unavailable Secs—Number of unavailable seconds encountered by the SONET Line in the current
15-minute interval.

SONET Far End Line Error Statistics

The SONET Far End Line Error Statistics area contains the following information:

•

Errored Secs—Number of far end errored seconds encountered by the SONET Line in the current
15-minute interval.

•

Severely Err Secs—Number of severely far end errored seconds encountered by the SONET Line in
the current 15-minute interval.

•

Coding Violations—Number of far end coding violations encountered by the SONET Line in the
current 15-minute interval.

•

Unavailable Secs—Number of far end unavailable seconds encountered by the SONET Line in the
current 15-minute interval.

SONET Path Error Statistics

The SONET Path Error Statistics area contains the following information:

•

Errored Secs—Number of errored seconds encountered by the SONET Path in the current 15-minute
interval.

•

Severely Err Secs—Number of severely errored seconds encountered by the SONET Path in the
current 15-minute interval.

•

Coding Violations—Number of coding violations encountered by the SONET Path in the current
15-minute interval.

•

Unavailable Secs—Number of unavailable seconds encountered by the SONET Path in the current
15-minute interval.

SONET Far End Path Error Statistics

The SONET Far End Path Error Statistics area contains the following information:

•

Errored Secs—Number of far end errored seconds encountered by the SONET Path in the current
15-minute interval.

•

Severely Err Secs—Number of far end severely errored seconds encountered by the SONET Path in
the current 15-minute interval.

•

Coding Violations—Number of far end coding violations encountered by the SONET Path in the
current 15-minute interval.

•

Unavailable Secs—Number of far end unavailable seconds encountered by the SONET Path in the
current 15-minute interval.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Search results

Summary of Contents for WS-C3550-12G

Reviews:

Brands by name

Popular brands

Cisco WS-C3550-12G, User Manual

Search results

Summary of Contents for WS-C3550-12G

Reviews:

Brands by name

Popular brands