manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 310

 

10-2

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 10      Virtual Interface Management

VTP Management Window

VTP Management Window

The VTP Management window allows you to configure VTP domains on the switch or router. This 
window can be launched from a Software object or VTP object within the Physical view.

To launch the VTP Management window, perform one of the following:

•

Right–click a Site object within the Network or Physical containment views, then choose 
CSM/7600 Manager > Logical > Software > Virtual Interface > VTP.

•

Right–click a Network Element object within the Network or Physical containment views, then 
choose Logical > Software > Virtual Interface > VTP.

•

Right–click a Software object within the Physical containment view, then choose 
Virtual Interface > VTP.

•

Right–click a VTP object within the Physical containment view, then choose VTP.

The following figure is an example of the VTP Management window.

Figure 10-1 VTP Management Window

You can choose more than one Software object at a time from the object list on the left side of the 
window.

The following tabs are available on the VTP Management window:

•

Details Tab

•

Additional Notes Tab

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands