manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 280

 

9-16

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 9      Software Management

STP Configuration Window

STP Configuration Window

The STP Configuration window provides information on the global Spanning Tree Protocol 
configuration on a managed Catalyst switch. This window is launched from the Software object or STP 
object in the Physical view.

To launch the STP Configuration window, perform one of the following:

•

Right–click a Site object within the Network or Physical containment views, then choose 
CSM/7600 Manager > Logical > Software > STP.

•

Right–click a Network Element object within the Network or Physical containment views, then 
choose Logical > Software > STP.

•

Right–click a Software object within the Physical containment view, then choose STP.

•

Right–click an STP object within the Physical containment view, then choose STP.

The following figure is an example of the STP Configuration Management window.

Figure 9-4

STP Configuration Window

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands