manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual, Page: 138 / 436

Share
Download
Cisco WS-C3550-12G User Manual Download Page 138

 

7-26

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 7      Module and Port Adapter Management

SLB Module Management Window

–

Minimum Connections—When the maximum connections is exceeded, no more connections 
will be established to the real server until the number of connections falls below this value. The 
valid values range from 0 to 4294967295. This value must be less than the currently configured 
maximum connections.

–

Maximum Connections—Maximum number of active connections on the real server at any one 
point. If the value is set to the maximum of 4294967295, it indicates that the maximum is 
infinite (not monitored). This value must be greater than the currently configured minimum 
connections.

Server Farm Config 

The Server Farm Config area allows you to add and configure server farms. The following attributes are 
configured:

•

Server Farm Name—Unique identifier of a server farm on the device.

•

Server Farm Add—Adds the server farm specified in the Server Farm Name field. You need to 
specify a name in the Server Farm Name field for the action to take effect.

•

Server Farm Remove—Removes the server farm that is selected in the Server Farm Table. A dialog 
box appears, asking you to confirm the action.

Real Server Config Subarea

This subarea allows the user to add and remove real servers to the server farm specified in the Server 
Farm Name field.

•

Real IP Address—IP address of the real server.

•

TCP Port—Optional TCP Port translation for the real server.

•

Real Server Add—Adds the real server specified by the Real IP Address, TCP Port, and Server Farm 
Name fields. You need to specify a name in the Server Farm Name field, an IP address in the Real 
IP Address field, and a port number in the TCP Port field for the action to take effect.

•

Real Server Remove—Removes the real server specified by the Real IP Address, TCP Port, and 
Server Farm Name fields. You need to specify a name in the Server Farm Name field, an IP address 
in the Real IP Address field, and a port number in the TCP Port field for the action to take effect.

Virtual Servers Tab

The following areas are available on the Virtual Servers tab of the SLB Module Management window:

•

Virtual Server 

•

Virtual Server Config 

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments