manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 390

 

12-2

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 12      Profile Management

Network Element Profile

Network Element Profile

The Network Element profile sets up a standard template for the Network Element object attributes listed 
below. These attributes are discussed in detail in the 

“Network Element Management Window” section 

on page 5-4

.

•

System Location

•

System Contact

•

Telnet Password

•

Enable Password

•

SNMP Trap Enabled

Network element profiles are created using the Network Element Management Profile window. 

To launch the Network Element Management Profile window, perform one of the following:

•

Right–click a Site object within the Network or Physical containment views, then choose 
CSM/7600 Manager > NE Config/Mgmt Profile.

•

Right–click a Network Element object within the Network or Physical containment views, then 
choose NE Config/Mgmt Profile.

The following figure is an example of the Network Element Management Profile window.

Figure 12-1 Network Element Management Profile Window

Using this window you can perform the following tasks:

•

Creating a Network Element Profile

•

Applying a Network Element Profile

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands