Cisco WS-C3550-12G User Manual Download Page 323 | Manualshive

Page: 323 / 436

background image

10-15

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 10 Virtual Interface Management

VLAN Management Window

Global Tab

The Global tab of the VLAN Management window consists of a single area, 802.1Q Trunk Remapped
VLANs. This area lists the mappings between 802.1Q and ISL VLANs. The information in this area is
common to all VLAN objects for a particular switch or router:

•

802.1Q Trunk Remapped VLANs Table—This table lists the following:

–

802.1Q VLAN Number—The 802.1Q VLAN number to be mapped.

–

ISL VLAN Number—The ISL VLAN to which the 802.1Q VLAN number is to be mapped.

•

Add/Remove Mapping—Adds or removes a mapping. Launches the VLAN Management—Mapping
Configuration window. A maximum of eight mappings are supported by the Catalyst switch.

Figure 10-7 VLAN Management—Mapping Configuration Window

Note

The valid range for 802.1Q VLAN number is 1 to 4095 for Native IOS and from 1001 to 4095
for Hybrid or pure CatOS. The valid range of ISL VLAN numbers is 1 to 1005 for Native IOS
and 1 to 1000 for Hybrid or pure CatOS.

The following is displayed on the VLAN Management—Mapping Configuration window:

–

ISL VLAN Number—The ISL VLAN to which the 802.1Q VLAN number is to be mapped.

–

802.1Q VLAN Number—The 802.1Q VLAN number to be mapped.

–

Add Mapping—Adds mapping of 802.1Q and ISL VLANs specified by the 802.1Q VLAN
Number and ISL VLAN Number fields.

–

Remove Mapping—Removes mapping of 802.1Q and ISL VLANs specified by the 802.1Q
VLAN Number and ISL VLAN Number fields.

«
...
321
322
323
324
325
...
»

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WS-C3550-12G

Brand: Z-Com Pages: 66

Brand: TRENDnet Pages: 36

Brand: Qcom Pages: 29

Brand: TP-Link Pages: 86

Brand: Billion Pages: 61

Brand: Billion Pages: 7

Brand: RocketFish Pages: 73

Brand: Fibocom Pages: 61

Brand: Aruba Pages: 2

Brand: Cambium Networks Pages: 34

Brand: Icom Pages: 90

Brand: Lynxspring Pages: 16

Brand: Ebyte Pages: 38

Brand: Tenda Pages: 2

Brand: Ebyte Pages: 21

Brand: Belair Pages: 255

Brand: Ubiquiti Pages: 15

Air Access ZA-5000 Series

Brand: ZDC Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands