Home
/
Cisco
/
WS-C3550-12G
/
User Manual

Cisco WS-C3550-12G, User Manual

Share

Page: 403 / 436

Cisco WS-C3550-12G User Manual Download Page 403

13-5

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 13 Alarms and Alarm Management

Cisco Catalyst Switch Manager Alarms

Cisco Catalyst Switch Manager Alarms

The Cisco Catalyst Switch Manager generates three types of alarms:

•

SNMP Trap Alarms—Cisco EMF alarms based on SNMP traps emitted by the Catalyst switch
running IOS.

•

Object State Alarms—Cisco EMF alarms based on the state of the Cisco Catalyst Switch Manager
objects.

•

Attribute Value Alarms—Cisco EMF alarms based on values of Cisco Catalyst Switch Manager
object attributes.

SNMP Trap Alarms

The following table lists the SNMP traps supported by a Catalyst switch and the corresponding
Cisco EMF alarm.

Table 13-2 Cisco EMF Alarms Generated by SNMP Traps

Trap/Varbind

Message

Alarm
Severity Object

Alarms Cleared

coldStart

C6576M:0132_0 Cold
Start:
Agent reinitializing;
configuration may have
changed.

Major

Network
Element

coldStart
ciscoEnvMonShutdownNotificat
ion
whyReload

warmStart

C6576M:0132_0 Warm
Start:
Agent reinitializing:
configuration may have
changed.

Major

Network
Element

warmStart

authenticationFailure

C6576M:0133_0
Authentication
Failure: Unauthorized
SNMP access.

Minor

Network
Element

None

linkUp

C6576M:0136_0 link
<ifDescr> up.

Normal

Interface

linkUp
linkDown

linkDown

C6576M:0136_0 link
<ifDescr> down.

Major

Interface

linkUp
linkDown

risingAlarm

RMON rising alarm-
index: <alarmIndex>,
variable:
<alarmVariable>,
threshold:
<alarmRisingThreshold
>, value: <alarmValue>,
type of sampling:
<alarmSampleType>

Informa
tional

Network
Element

risingAlarm

«
...
401
402
403
404
405
...
»

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands