manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 153

 

8-7

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

Ethernet Interface Management Window

–

e1000BaseZX

•

Operational Status—Displays the operational status of the interface. This attribute is read-only and 
has one of the following values:

–

up—Interface is ready to transmit and receive packets.

–

down—No packets are being passed. The interface is in this state if there is a fault preventing 
it from going to the up state.

–

testing—No operational packets can be passed.

–

unknown

–

dormant—Interface is up but waiting for external actions.

–

notPresent—The interface is in this state if the interface has missing components (typically 
hardware).

–

lowerLayerDown—The interface in the lower layer is down.

•

Administrative Status—Displays the administrative status of the interface. These are the values:

–

up—The interface is up and operational.

–

down—The interface is in a down administrative status; this value causes the operational status 
to be set to down as well.

–

testing (read-only)—In this state, no operational packets can be transmitted or received. This 
value is read-only.

•

Last Change—The timestamp indicating when the configuration for this interface was last changed. 
This is a read-only attribute.

•

Connector Present—Displays if a cable is attached to the interface. These are the values:

–

yes

–

no

–

unknown—This value is used when the Administrative Status is not set to “up”. In this case, it 
cannot be determined if a connection is present or not.

•

Number of Resets—The number of times this interface has been reset. This attribute is read-only.

Configuration Tab

The following areas are available on the Configuration tab of the Ethernet Interface Management 
window:

•

General 

•

Layer 2 

•

Layer 3 

•

Private VLAN Edge 

•

Actions

•

802.1Q Tunneling 

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands