Cisco WS-C3550-12G User Manual Download Page 377

Page: 377 / 436

11-25

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 11 Routing Management

BGP Management Window

Figure 11-10 BGP Management—Configure Path Window

The following is displayed on the BGP Management—Configure Path window:

–

Local AS—Indicates the BGP autonomous system number enabled.

–

IP Address—IP address of the local network to be added to or removed from the local network
table.

–

Wildcard Mask—Mask to be used with the IP address.

–

Add Local Network—Adds the specified entry from the local network table.

–

Remove Local Network—Removes the specified entry from the local network table.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Search results

Summary of Contents for WS-C3550-12G

Reviews:

Brands by name

Popular brands

Cisco WS-C3550-12G, User Manual

Search results

Summary of Contents for WS-C3550-12G

Reviews:

Brands by name

Popular brands