B337EN4_4
Operation
4-137
Alignment ON
•
Duration:
−
Enter the duration for igniting the beam using the pulse
trigger switch. This value may not be greater than 600000
ms.
•
Laser output:
−
PULSING F: enter value between 1% and 10%
•
Gating frequency:
−
Enter a value between 100 Hz and 99 kHz (rounded up to
the nearest 10 Hz). The smallest value is 100 Hz
Laser status
•
Laser output: current laser output in watts.
•
System pressure: current gas pressure in the resonator in
hPa
•
Resonator status:
−
Start-up: after the laser is switched on with the Laser
ON/OFF button, the automatic power-up cycle will start and
the resonator status "Start-up" will be displayed.
−
Operating: once the power-up cycle has been completed,
the resonator is at the working pressure and the nominal
RPM of the radial turbine blower is reached. The laser is
ready for operation.
−
Run down: after the laser is switched off with the Laser
ON/OFF button, the automatic shutdown cycle will start and
the resonator status "Run down" will be displayed.
−
At rest: once the shutdown cycle has been completed, the
resonator will have the system pressure 1100 hPa. The
control system can be switched off.
−
Leakage test: this resonator status is displayed if the
leakage test has been started via "DIAGNOSTICS - Laser -
Leakage test".
−
Switch elements: this resonator status is displayed if the
switch elements for TLF laser intervention 1 or 2 have been
activated. In this case, the laser can then only be operated
by means of the switch elements. The laser status resulting
from operating switch elements is reset to the initial status
as soon as the switch elements are deactivated.
•
Active operation mode: the active operating mode of the laser
is displayed.
−
Operating modes with service mode OFF: LPC normal, LPC
analog, LPC cycles.
−
Operating modes with service mode ON: Alignment On,
Alignment Off
•
Active submode: the active submode is displayed. Possible
submodes of the laser are: CW, PULSING F, PULSING T.
Содержание LASERCELL 1005
