Leica Captivate Скачать руководство пользователя страница 1049

Страница: 1049 / 1060

fixed while moving. A new initialisation starts automatically when, after losing

the minimum number of required satellites, enough satellites are tracked again.

The instrument source describes where the coordinate triplet was measured or

entered. The options are GS, TS, Infinity or Level.

The procedures, codes and protocols that enable two entities to interact for an

exchange of data. Each interface is given a meaningful display name which

enables easy distinction between interfaces.

I.10

I.11

I.12

I.13

I.14

etworked

ransport of

TCM using

nternet

rotocol

•

is a protocol streaming real-time corrections over the Internet.

•

is a generic protocol based on the Hypertext Transfer Protocol HTTP/1.1.

•

is used to send differential correction data or other kinds of streaming

data to stationary or mobile users over the Internet. This process allows

simultaneous computer, laptop, PDA, or instrument connections to a

broadcasting host.

•

supports wireless Internet access through mobile IP networks like digital

cellular phones or modems.

The Ntrip Server could be the GS itself. This setup means the GS is both the

Ntrip Source generating the real-time data and also the NTRIP Server transfer-

ring this data to the Ntrip Caster.

NTRiPCas

ter

InternetSe

rver

GS_044

NTRiPClient

NTRiPServer

Ntrip and its role in the Inter-

net

The Ntrip Caster

•

is an Internet server handling various data streams to and from the Ntrip

Servers and Ntrip Clients.

•

checks the requests from Ntrip Clients and Ntrip Servers to see if they are

registered to receive or provide real-time corrections.

•

decides whether there is streaming data to be sent or to be received.

The Ntrip Client receives data streams. This setup could be, for example a real-

time rover receiving real-time corrections.

Instrument source

Interface

Ntrip

Ntrip Caster

Ntrip Client

Glossary

1049

«
...
1047
1048
1049
1050
1051
...
»

Содержание Captivate





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Captivate

Отзывы:

Похожие инструкции для Captivate

Бренды по названию

Популярные бренды

Leica Captivate, Техническое справочное руководство

Результаты поиска

Содержание Captivate

Отзывы:

Похожие инструкции для Captivate

Бренды по названию

Популярные бренды