manualshive.com logo in svg

Abbott CELL-DYN 3000, Руководство оператора

Поделиться
Скачать
Abbott CELL-DYN 3000 Скачать руководство пользователя страница 98

CELL-DYN

 3000 System Operator’s Manual 

3-25

9140240E — May 1995

Chapter 3 Principles of Operation

Hemoglobin Measurement

Overview

The HGB channel is used for the colorimetric determination of 
Hemoglobin. 

A 1:251 dilution of the sample is made with the diluent and the 
Hemoglobin Lyse reagent in the HGB mixing chamber. The HGB 
concentration is measured using a modified hemiglobincyanide method. 
A filtered LED with a wavelength of 540 nm is the light source. A 
photodetector measures the light that is transmitted.

Hemoglobin Measurement Process

The Hemoglobin Lyse reagent lyses the diluted red blood cells and 
converts the Hemoglobin that is released to a cyanide-containing 
pigment. The sample is transferred to the Hemoglobin flow cell where 
the Hemoglobin concentration is measured. The sample enters the flow 
cell from the bottom. This allows any bubbles present to float to the 
surface so they will not interfere with the reading.

The LED shines through the flow cell and a 540 nm narrow bandwidth 
filter onto a photodetector. The Hemoglobin concentration is directly 
proportional to the absorbance of the sample at 540 nm. Five separate 
HGB readings are made on each sample and averaged to give the final 
HGB sample reading. After the Hemoglobin readings have been made, 
the HGB flow cell is rinsed with Hemoglobin Lyse.

The rinse is drained and more HGB Lyse reagent is delivered to the HGB 
flow cell. A zero or blank reading is then obtained on the reagent to 
provide a reference to which the sample signal is compared. Five 
separate blank readings are made on each sample and averaged to give 
the final HGB reference reading.

The reference and sample readings are compared to determine the HGB 
concentration of the sample. The HGB result is expressed in grams of 
Hemoglobin per deciliter of whole blood. 

HGB Parameter

The Hemoglobin is directly measured and is expressed in grams of 
Hemoglobin per deciliter of whole blood.

HGB Flagging

Refer to the “

Operational Messages and Data Flagging

” section of this 

chapter for 

HGB flagging

 information.

Search

Go Back

Book TOC

Содержание CELL-DYN 3000































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды