Xerox PHASER 8560MFP Service Documentation Download Page 181

Page: 181 / 296

10/2006

4-67

Phaser 8510/8560MFP Multifunction Product

REP 6.0.6, REP 6.0.7

Repairs and Adjustments

Initial Issue

Figure 2 Removing the Waste Tray Cover

Disconnect the Waste Tray Detect Sensor (P/J110) from the I/O Board.

Unlace the sensor harness from the retainers and guides.

10. Release the hooks that secure the sensor to the cover and remove the sensor.

Figure 3 Removing the Waste Tray Detect Sensor.

Replacement

Perform the Head Tilt Gear (ADJ 4.13.1), and Process Drive Alignment (ADJ 4.7.1) adjust-
ments before restoring system power.

REP 6.0.7 Paper Size Switch

Parts List on PL 6.0

Removal

Remove the Scanner Assembly with attached DADF (REP 1.0.11).

Remove the Output Tray (REP 1.0.6).

Remove the Right Side Cover (REP 1.0.21).

Remove Tray 2.

Disconnect the Paper Size Switch (P/J600) from the I/O Board.

Unlace the harness from the retainers.

Use pliers to push the latch rearward and release the front of the switch from the chassis.

Figure 1 Removing the Paper Size Switch

Pull the harness through the opening in the chassis and remove the switch from the tray
cavity.

Summary of Contents for PHASER 8560MFP









































































































































































































































































































Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands

Xerox PHASER 8560MFP, Service Documentation

Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands