10/2006
7-3
Phaser 8510/8560MFP Multifunction Product
Wiring Data
Initial Issue
How to use the Plug/Jack Location List
The P/J Locator diagrams show the location of primary connections within the system. Use
these illustrations to locate connections called out in the procedures presented in Sections 2,
4, and 6. Connectors designated “CN” are listed at the end of the P/J connectors.
To find the location of a Plug or Jack:
1.
Locate the P/J connector designator in the first column of the table.
2.
With this information, go to the map (Figure Number) listed in the second column.
3.
Use the coordinates to quickly locate the connection indicated on the map with its P/J
designation number.
Table 1 Plug / Jack Location List
P/J
Map
Coordinates Remarks
0150
Figure 3
Connects the I/O Board to the Ink Loader Assembly.
0670
Figure 3
C-107
Connects the Preheater sensor to the Preheater Board
0720
Figure 11 C-104
Connects the Preheater Board to the Right Side Harness.
1
Figure 6
H-105
Connects the Electronics Module to Door Interlocks and
Motors.
2
Figure 6
G-105
Connects the Electronics Module to the Scanner Power Sup-
ply and Exit Module Control Board.
3
Figure 6
G-105
Connects the Electronics Module to the Printhead.
4
Figure 6
I-106
Connects the System Power Supply to the Printhead Heat-
ers.
5
Figure 6
E-106
Connects the System Power Supply to the Ink Melt Heaters.
6
Figure 4
D-104
Connects the System Power Supply to the Scanner Power
Supply.
7
Figure 4
D-105
Connects the System Power Supply to the Preheater and
Drum Heater Relay Boards.
8
Figure 4
C-108
Connects AC Line to the System Power Supply
9
Figure 4
C-109
Connects the Right Side Harness to the Electronics Module.
10
Figure 4
F-109
Connects the Electronic Module to the I/O Board.
11
Figure 4
E-109
The system Ethernet LAN Port.
12
Figure 4
F-107
Connects the system to the FAX line.
13
Figure 4
E-107
The system USB Port.
14
Figure 4
E-105
The system Serial Debug Port
15
Figure 4
E-104
Connects the Electronics Module to the DADF.
16
Figure 5
C-109
Connects the Electronics Module to the Wave Amplifier.
17
Figure 5
E-109
Connects the Left Side Harness to the Electronics Module.
18
Figure 5
G-109
Connects the Electronics Module to the Y-Axis Motor.
19
Figure 3
D-104
Connects the Control Panel to the Scanner Assembly.
22
Figure 8
C-105
Connects the Electronics Module and Exit Module Control
Board to the Scanner Power Supply.
110
Figure 9
B-107
Connects the Waste Tray Detect Sensor to the I/O Board.
118
Figure 2
C-107
Connects the Drum Fan to the Right Side Harness.
120
Figure 2
C-107
Connects the Drum Encoder to the Right Side Harness.
125
Figure 6
Connects the Process Motor to the Right Side Harness.
130
Figure 2 F-104
Connects the Printhead Wiper Clutch to the I/O Board.
140
Figure 2
D-104
Connects the Front Door Interlock to the Exit Module Har-
ness.
150
Figure 2
H-106
Connects the X-Axis Motor to the Right Side Harness.
171
Figure 3
C-108
Connects the No Paper Sensor to the I/O Board.
172
Figure 3
D-108
Connects the Paper Height Sensor to the I/O Board.
180
Figure 7
Connects the Electronics Module to the Printhead.
200
Figure 10 E-108
Connects the Drum Heater to the Relay Board.
202
Figure 1
H-107
Connects the Preheater Lift Solenoid to the Left Side Har-
ness.
203
Figure 1
C-108
Connects the Tray 2 Lift Motor to the Left Side Harness.
204
Figure 4
Connects the Optional Feeder to the Left Side Harness.
206
Figure 1
E-104
Connects the Media Drive Motor to the Left Side Harness.
207
Figure 1
B-107
Connects the Electronics Module Fan to the Left Side Har-
ness.
208
Figure 1
C-107
Connects the Head Tilt Solenoid to the Left Side Harness.
210
Figure 10 E-104
Connects the Relay Board to the Electronics Module.
212
Figure 1
A-104
Connects the Purge Pump to the Left Side Harness.
220
Figure 10 E-108
Connects the Relay Board to the Electronics Module.
230
Figure 1
F-108
Connects the Tray 2 Pick Clutch to the Left Side Harness.
240
(fig 18)
Connects the Wave Amplifier to the Printhead.
241
Figure 1
G-108
Connects the Tray 1 Pick Solenoid to the Left Side Harness
250
Figure 9
E-105
Connects the Strip Solenoid to the I/O Board.
256
Figure 1
H-106
Connects the Deskew Clutch to the Left Side Harness.
270
Figure 9
G-104
No Connection on the I/O Board.
303
Figure 1
F-103
Connects the Elevator Position Sensor, Scanner Detect Sen-
sor, Speaker, and Elevator Motor to the Exit Module Har-
ness.
304
Figure 1
Connects the Elevator Position Sensor to the Elevator Motor
Harness
308
Figure 1
C-103
Interconnects two branches of the Exit Module harness.
309
Figure 2
F-102
Connects the Exit Roller Motor to the Exit Module Harness.
320
Figure 1
Connects the Exit Elevator Motor to the Exit Module Har-
ness.
400
Figure 9
B-108
Connects the I/O Board to the Preheater, Tray 2 Sensors,
and Relay Board.
409
Figure 1
E-102
Connects the Elevator Position Sensor to the Front Exit
Module Harness.
410
Figure 1
Connects the Speaker to the Exit Module Harness.
411
Figure 1
G-104
Connects the Exit Door Interlock to the Exit Module Harness.
Table 1 Plug / Jack Location List
P/J
Map
Coordinates Remarks
Summary of Contents for PHASER 8560MFP
