Xerox PHASER 8560MFP Service Documentation Download Page 68

Page: 68 / 296

10/2006

2-42

Phaser 8510/8560MFP Multifunction Product

37,024.48, 37,026.44

Initial Issue

Error Messages and Codes

37,024.48 PEST Tray 2 Lift Motor Fault

An error has occurred related to the Tray 2 Lift Motor. The following troubleshooting procedure
applies to this error:.

Initial Actions

•

Check the Tray 2 Lift Plate for damage or obstructions.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

37,026.44 PEST Purge Pump Fault

An error has occurred related to the Purge Pump. The following troubleshooting procedure
applies to this error:.

Initial Actions

•

Check the Purge Pump for damage or obstructions.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

Tray 2 Lift Motor Fault

37,024.48 The Tray 2 Lift Motor is drawing less power than expected.

Table 1 37,024.48 Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

Tray 2 Lift Motor, PL 4.0

Left Side Harness (1/2), Figure 4

Electronics Module, PL 4.0

Left Side Harness (1/2), Figure 4

Table 2 PEST Tray 2 Lift Motor Fault Troubleshooting Procedure

Step Questions or Actions

Yes

Test the Tray 2 Lift Motor.
Run the Service Diagnostics Tray 2 Lift
Motor test.
Does the motor operate correctly?

Replace the Elec-
tronics Module (REP
5.0.5).

Go to Step 2.

Check the motor connection to the Left
Side Harness.
Is the connection secure and the harness
undamaged?

Replace the motor
(REP 4.0.10).

Repair of replace the
Left Side Harness.

Tray 2 Lift Motor Fault

37,026.44 The Purge Pump purge valve is drawing less power than expected.

Table 1 37,026.44 Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

Purge Pump, PL 2.0

Left Side Harness (2/2), Figure 5

Electronics Module, PL 4.0

Left Side Harness (2/2), Figure 5

Table 2 PEST Purge Pump Fault Troubleshooting Procedure

Step Questions or Actions

Yes

Test the Purge Pump.
Run the Service Diagnostics Purge Vent
Solenoid test.
Does the pump operate correctly?

Go to Step 2.

Replace the Purge
Pump (REP 2.0.7).

Check the pump connection to the Left
Side Harness.
Is the connection secure and the harness
undamaged?

Replace the Purge
Pump (REP 2.0.7).

Repair of replace the
Left Side Harness.

Summary of Contents for PHASER 8560MFP









































































































































































































































































































Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands

Xerox PHASER 8560MFP, Service Documentation

Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands