Xerox PHASER 8560MFP Service Documentation Download Page 70

Page: 70 / 296

10/2006

2-44

Phaser 8510/8560MFP Multifunction Product

37,035.44 and 37,036.45, 37,037.46 and 37,038.47

Initial Issue

Error Messages and Codes

37,035.44 and 37,036.45 PEST Y-Axis Motor Faults

A Y-Axis Motor error has occurred. The following troubleshooting procedure applies to these
errors:

Initial Actions

•

Check for obstructions to Drum rotation.

•

Check the condition of the Y-Axis Drive Belt.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

37,037.46 and 37,038.47 PEST Media Drive Faults

A Media Drive Assembly error has occurred. The following troubleshooting procedure applies
to these errors:

Initial Actions

•

Check for obstructions to Media Drive rotation.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

PEST Y-Axis Motor Faults

37,035.44 The Y-Axis Motor is drawing less power than expected.

37,036.45 The Y-Axis Motor is drawing too much power.

Table 1 37,03X.4x Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

Y-Axis Motor, PL 4.0

Electronics Module Power, Figure 7

Drum Assembly, PL 2.0

Electronics Module, PL 5.0

Electronics Module Power, Figure 7

Table 2 PEST Y-Axis Motor Faults Troubleshooting Procedure

Step Questions or Actions

Yes

Check the Drum rotation.
Does the Drum rotate smoothly?

Go to Step 2.

Replace the Drum
Assembly (REP
2.0.3).

Check the Y-Axis Motor.
Remove the Y-Axis Belt (REP 2.0.4).
Does the Y-Axis Motor shaft rotate freely?

Go to Step 3.

Replace the Y-Axis
Motor (REP 4.0.11).

Replace the Y-Axis Belt and test the Y-
Axis Motor.
Run the Service Diagnostics Y-Axis Drive
test.
Does the motor operate correctly?

Replace the Elec-
tronics Module (REP
5.0.5).

Go to Step 4.

Check wiring to the motor.
Is the wiring damaged?

Repair or replace the
harness.

Replace the Y-Axis
Motor (REP 4.0.11).

PEST Media Drive Faults

37,037.46 The Media Drive Motor is drawing less power than expected.

37,038.47 The Media Drive Motor is drawing too much power.

Table 1 37,037.46 and 37,038.47 Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

Media Drive, PL 4.0

Left Side Harness (2/2), Figure 5

Electronics Module, PL 5.0

Left Side Wire Routing (2/2), Figure 5

Table 2 PEST Media Drive Faults Troubleshooting Procedure

Step Questions or Actions

Yes

Test the Media Drive Motor.
Run the Service Diagnostics Media Path
Motor test.
Does the motor operate correctly?

Replace the Elec-
tronics Module (REP
5.0.5).

Go to Step 2.

Check wiring to the motor.
Is the wiring damaged?

Repair or replace the
harness.

Replace the Media
Drive (REP 4.0.14).

Summary of Contents for PHASER 8560MFP









































































































































































































































































































Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands

Xerox PHASER 8560MFP, Service Documentation

Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands