Xerox PHASER 8560MFP Service Documentation Download Page 37

Page: 37 / 296

10/2006

2-11

Phaser 8510/8560MFP Multifunction Product

3,0XX.6x, 4,0xx.4x

Error Messages and Codes

Initial Issue

3,0XX.6x IPC Program Faults

A firmware communications error has occurred. The following troubleshooting procedure
applies to these errors:

Initial Actions

•

Reset NVRAM and retest.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

4,0xx.4x Process Control Errors

The following troubleshooting procedure applies to these errors:

Initial Actions

•

Check the ambient air temperature.

•

Check that the system is located in a suitable environment.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

Table 1 3,000.6x Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

NVRAM, PL 5.0

Table 2 I/O Board Error Troubleshooting Procedure

Step Questions or Actions

Yes

Reseat all Electronics Module connec-
tions.
Does the problem persist?

Go to Step 2.

Complete.

Check ground integrity.
Are the system grounds connected?

Reset NVRAM. If the
error persists,
replace the NVRAM
device (REP 5.0.9).

Reconnect the sys-
tem grounds.

Process Control Errors

4,017.47

The ambient temperature is too low ( < 10

C).

4,018.48

The Printhead temperature is too low.

4,020.41

Fast Time To Ready (FTTR) mode with head/cap flag set in NVRAM.

4,021.42

Fast Time To Ready (FTTR) mode with a dirty Drum.

Table 1 4,0xx.4x Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

Electronics Module, PL 5.0

Right Side Wire Routing (2/2), Figure 3

Printhead, PL 2.0

Electronics Module, Figure 6

Drum Assembly, PL 2.0

Electronics Module Power, Figure 7

Drum Heater Relay Board, PL 5.0 Right Side Wire Routing (1/2), Figure 2

Drum Temperature Sensor, PL 6.0 I/O Board (2/2), Figure 10

Table 2 Process Control Error Troubleshooting Procedure

Step Questions or Actions

Yes

Test the heaters.
Run the Service Diagnostics Monitor
Heaters tests with all heaters On.
Do the heaters function properly?

Replace the Elec-
tronics Module (REP
5.0.5).

Go to Step 3.

Check the harness to the failed heater.
Is the harness damaged?

Replace the har-
ness.

Replace the failed
component.

Summary of Contents for PHASER 8560MFP









































































































































































































































































































Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands

Xerox PHASER 8560MFP, Service Documentation

Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands