Xerox PHASER 8560MFP Service Documentation Download Page 43

Page: 43 / 296

10/2006

2-17

Phaser 8510/8560MFP Multifunction Product

7,007.49, 7,008.41

Error Messages and Codes

Initial Issue

7,007.49 Process Drive Fault

A Process Drive or Printhead error has occurred. The following troubleshooting procedures
applies to this error:

Initial Actions

•

Check that the Process Drive gear train is properly homed.

•

Check for obstructions or ink spills around the Printhead.

•

Verify the Printhead travels smoothly from left to right.

•

Check the Printhead Restraint Arms.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

7,008.41 Printhead Tilt Fault

A Process Drive or Printhead error has occurred. The following troubleshooting procedure
applies to this error:

Initial Actions

•

Check that the Process Drive gear train is properly homed.

•

Check for obstructions or ink spills around the Printhead.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

The Head Tilt Solenoid is not activating the head tilt cam, or the head is not tilting properly

Process Drive Fault

7,007.49

The Process Drive stalled while tilting the Printhead.

Table 1 7,007.49 Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

Process Drive, PL 4.0

Right Side Harness / I/O Control, Figure 8

Table 2 Process Drive Faults 7,007.49 Troubleshooting Procedure

Step Questions or Actions

Yes

Check that the Process Drive is properly
aligned (ADJ 4.7.1).
Is the Process Drive misaligned?

Perform ADJ 4.7.1.

Go to Step 2.

Remove the Printhead and inspect the
Head Tilt Gear, Spring, and Process Drive
gears for ink spills.
Clean if necessary.
Does the error persist?

Go to Step 3.

Complete.

Realign the Process Drive (ADJ 4.7.1).
Does the error persist?

Replace the Pro-
cess Drive (REP
4.0.7).

Complete.

Process Faults

7,008.41

Printhead tilt is not engaged, or the Printhead is stuck in the tilt position.

Table 1 7,008.41 Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

Process Drive, PL 4.0

Right Side Harness / I/O Control, Figure 8

Head Tilt Solenoid, PL 4.0 Left Side Harness (2/2), Figure 5

Head Tilt Gear, PL 4.0

Table 2 Head Tilt Solenoid Faults 7,008.41 Troubleshooting Procedure

Step Questions or Actions

Yes

Reboot the system.
Does the error persist?

Go to Step 2.

Complete.

Check for Ink spills on or near the Head
Tilt Gear.
Clean and reboot the system.
Does the error persist?

Go to Step 3.

Complete.

Check that the Printhead moves properly
to the left and right.
Does the Printhead move correctly?

Go to Step 4.

Remove any
obstructions or
replace any defec-
tive parts.

Realign the Process Drive (ADJ 4.7.1).
Does the error persist?

Go to Step 5.

Complete.

Check the Process Drive for damage,
debris, or obstructions.
Is there any damage?

Replace the Pro-
cess Drive (REP
4.0.7).

Go to Step 6.

Test the Tilt Axis Drive.
Run the Service Diagnostics Tilt Axis
Drive test.
Did the test pass?

Go to Step 7.

Replace the Pro-
cess Drive (REP
4.0.7).

Summary of Contents for PHASER 8560MFP









































































































































































































































































































Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands

Xerox PHASER 8560MFP, Service Documentation

Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands