Xerox PHASER 8560MFP Service Documentation Download Page 42

Page: 42 / 296

10/2006

2-16

Phaser 8510/8560MFP Multifunction Product

7,002.44, 7,006.4x

Initial Issue

Error Messages and Codes

7,002.44 Process Drive Fault

A Process Drive error has occurred. The following troubleshooting procedure applies to this
error:

Initial Actions

•

Check that the Process Drive gear train is properly homed.

•

Check for obstructions in or around the Process Drive gearbox.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

7,006.4x Head Tilt Solenoid Fault

A Printhead tilt error has occurred. The following troubleshooting procedure applies to this
error:

Initial Actions

•

Check for obstructions or ink spills around the Printhead.

•

Verify the Printhead travels smoothly from left to right.

•

Check the Printhead Restraint Arms.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedures

The Head Tilt Solenoid is not activating the Head Tilt Gear, or the Printhead is not tilting prop-
erly

Process Faults

7,002.44

The Process Drive stalled during operation.

Table 1 7,002.44 Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

Process Drive, PL 4.0

Right Side Harness / I/O Control, Figure 8

Table 2 Process Drive Fault 7,002.44 Troubleshooting Procedure

Step Questions or Actions

Yes

Check that the Process Drive is properly
aligned (ADJ 4.7.1).
Is the Process Drive misaligned?

Perform ADJ 4.7.1.

Go to Step 2.

Test the Tilt Axis Drive.
Run the Service Diagnostics Tilt Axis
Drive test.
Did the test pass?

Go to Step 3.

Go to Step 4.

Check the Process Drive for damage,
debris, or obstructions.
Is there any damage?

Replace the Pro-
cess Drive (REP
4.0.7).

Go to Step 4.

Test the Process Drive Motor.
Run the Service Diagnostics Process
Motor Test.
Did the test fail?

Replace the Pro-
cess Drive (REP
4.0.7).

Go to Step 5.

Test the Transfix Cams
Run the Service Diagnostics Transfix
Drive Slow test.
Do the Transfix Cam operate correctly?

Replace the Pro-
cess Drive (REP
4.0.7).

Verify the transfix
cams are not dam-
aged. If the error
persists, replace the
Transfix Cam Shaft
(REP 2.0.10).

Process Faults

7,006.xx

The Head Tilt Solenoid is not activating the Head Tilt Cam, or the Print-
head is not tilting properly.

Table 1 7,0xx.4x Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

Head Tilt Gear, PL 4.0

Head Tilt Solenoid, PL 4.0 Left Side Harness (2/2), Figure 5

Process Drive, PL 4.0

Right Side Harness / I/O Control, Figure 8

Table 2 Head Tilt Solenoid Faults 7,006.xx Troubleshooting Procedure

Step Questions or Actions

Yes

Check that the Process Drive is properly
aligned (ADJ 4.7.1).
Is the Process Drive misaligned?

Perform ADJ 4.7.1.

Go to Step 2.

Reboot the system.
Is the tilt-head activating the Head Tilt
Gear.

Go to Step 4.

Go to Step 3.

Check for Ink spills on or near the Head
Tilt Gear.

Remove ink spills or
reinstall the head-tilt
and start over with
Step 1.

Go to Step 4.

Review instructions for 7,008.xx and
7,010.xx fault codes.

Follow recom-
mended actions for
error codes and
reboot the printer.

Summary of Contents for PHASER 8560MFP









































































































































































































































































































Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands

Xerox PHASER 8560MFP, Service Documentation

Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands