Xerox PHASER 8560MFP, Service Documentation

Page: 13 / 296

10/2006
xiii Phaser 8510/8560MFP Multifunction Product
System Configurations
Introduction Initial Issue
System Configurations
Standard Features
The Phaser 8510/8560MFP offers these standard features:
• Maximum print speed (pages per minute) based on letter-size plain paper:
NOTE: Print speeds for media fed from Tray 1 may be up to 50% slower.
• First-page-out: 8 seconds for color prints, 15 seconds for color copies
• Copy, Print, Scan, Fax capabilities (options vary according to configuration and memory)
• Connections: USB, Ethernet 10/100/1000 Base-Tx, RJ-11 Fax Modem, Foreign Device
Interface
Available Configurations
Table 2 lists the standard configurations.
Product Options
Phaser Multifunction Product options include:
• Additional Trays
• Memory
• System Cart
Additional Trays
Trays 1 and 2 are standard on all configurations. The following additional tray combinations are
supported:
• One 525-Sheet Feeder (Tray 3)
• Two 525-Sheet Feeders (Trays 3 and 4)
Memory
All configurations have two memory slots supporting 512 MB, and 1 GB SODIMM modules (up
to maximum of 1 GB DDR2).
System Cart
The System Cart supports a fully-optioned system and provides space for media storage.
Metered Printing
Metered printing (PagePack), involves the combination of control software and specialized Ink
Sticks to meter system activity for billing purposes. The Configuration page lists Metered Ink as
Enabled when metering is enabled.
Metered Operation
When a metered printer is initialized at first power-up, the customer sets the printer to Metered
operation using a unique, factory-supplied, 4-digit PIN. Once set to Metered operation, the con-
trol software performs the following:
1. The Mode and PIN-entered values in Engine Control Board NVRAM are set.
2. The Control Panel momentarily displays “Metered Ink is now enabled”, then returns to
“Ready” (if no other errors).
3. The First Time Tips pages and the Configuration page are printed.
If an incorrect PIN is entered, “Incorrect numeric password” displays with a prompt “Retry” or
“Do not retry.” Retry returns to the enter prompt, “Do not retry” returns to the Replace Ink Stick
error message. The error persists until the correct PIN is entered.
NOTE: The Hidden Service menu provides an Enable Metered Ink option to restore the
Metered mode parameters to NVRAM should they become lost or corrupt.
Metered Ink
To support metered printing, metered Ink Sticks are available in all four colors. The shape of
the metered Ink Stick differs from the non-metered versions.
Table 1 Phaser 8510/8560MFP Print Speeds
Phaser 8510MFP Multifunction Product Phaser 8560MFP Multifunction Product
PostScript Print Quality Modes:
–
Fast Color: 24 ppm
– Enhanced: 12 ppm
PostScript Print Quality Modes:
–
Fast Color: 30 ppm
– Standard: 24 ppm
– Enhanced: 16 ppm
– High Resolution/Photo: 10 ppm
PCL Print Quality Modes:
–
300 x 600 dpi: 13 ppm
– 600 x 600 dpi: 6 ppm
PCL Print Quality Modes:
–
300 x 600 dpi: 16 ppm
– 600 x 600 dpi: 8 ppm
Table 2 Phaser 8510/8560MFP Standard Configurations
Features 8510MFP/N 8510MFP/D 8560MFP/D 8560MFP/T 8560MFP/X
Memory 512 MB 512 MB
(2x256) 512 MB 512 MB 512 MB
Hard Drive No No Yes Yes Yes
Flash Disk Yes Yes No No No
Automatic 2-sided
Printing (DADF) No Yes Yes Yes Yes
525-Sheet Feeder No* No* No* Yes Yes
System Cart No* No* Yes Yes Yes
Copy Yes Yes Yes** Yes** Yes**
Scan to PC Yes Yes Yes Yes Yes
Scan to E-mail Yes Yes Yes Yes Yes
Scan to Hard Drive No No Yes Yes Yes
Fax Yes Yes Yes** Yes** Yes**
* This option can be purchased separately for this configuration.
** Hard Drive enables advanced features on this configuration.