Xerox PHASER 8560MFP Service Documentation Download Page 39

Page: 39 / 296

10/2006

2-13

Phaser 8510/8560MFP Multifunction Product

4,0xx.6x, 5,0xx.4x

Error Messages and Codes

Initial Issue

4,0xx.6x Process Control Program Faults

A firmware communications error has occurred. The following troubleshooting procedure
applies to these errors:

Initial Actions

•

Reset NVRAM and retest.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

5,0xx.4x Y-Axis Sub-System Faults

The following troubleshooting procedure applies to these errors:

Initial Actions

•

Check for obstructions or debris.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

Table 1 4,0xx.6x Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

NVRAM, PL 5.0

Table 2 Process Control Program Faults Troubleshooting Procedure

Step Questions or Actions

Yes

Reseat all Electronics Module connec-
tions.
Does the problem persist?

Go to Step 2.

Complete.

Check ground integrity.
Are the system grounds connected?

Reset NVRAM. If the
error persists,
replace the NVRAM
device (REP 5.0.9).

Reconnect the sys-
tem grounds.

Y-Axis Sub-System Faults

5,001.41

The Drum rotated once without a Drum Home Position Sensor activation.

5,002.42

The Y-Axis Encoder is faulty, or the Drum has stalled.

5,003.43

Problem in the Y-Axis sub-system.

5,004.44

Problem with the Y-Axis motion sub-system.

Table 1 5,0xx.4x Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

Y-Axis Belt, PL 2.0

Y--Axis Motor, PL 4.0

Electronics Module Power, Figure 7

Drum Assembly (Encoder) Right Side Harness / /O Control, Figure 8

Table 2 Y-Axis Sub-System Faults Troubleshooting Procedure

Step Questions or Actions

Yes

Test the Y-Axis Encoder.
Run the Service Diagnostics Y-Axis
Encoder test from the Monitor menu.
Did the test pass?

Go to Step 2.

Go to Step 3.

Check the Y-Axis Motor connection (P/
J18).
Is the wiring faulty?

Replace the wiring.

Go to Step 4.

Check the Y-Axis Encoder wiring.
Is the wiring faulty?

Replace the wiring.

Replace the Drum
Assy (REP 2.0.3).

Test the Y-Axis Drive.
Run the Service Diagnostics Y-Axis Drive
test.
Did the test pass?

Go to Step 5.

Replace the Y-Axis
Motor (REP 4.0.11).

Test Y-Axis Belt tension.
Run the Service Diagnostics Y-Axis Belt
Tension test.
Did the test pass?

Go to Step 6.

Replace the Y-Axis
Belt (REP 2.0.4).

Summary of Contents for PHASER 8560MFP









































































































































































































































































































Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands

Xerox PHASER 8560MFP, Service Documentation

Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands