Xerox PHASER 8560MFP Service Documentation Download Page 40

Page: 40 / 296

10/2006

2-14

Phaser 8510/8560MFP Multifunction Product

5,0xx.4x, 5,0xx.6x

Initial Issue

Error Messages and Codes

5,0xx.6x Y-Axis Sub-System Program Faults

A software error has occurred. The following troubleshooting procedure applies to these errors:

Initial Actions

•

Reset NVRAM and retest.

•

If the problem persists, follow the procedure below.

Primary Causes

The troubleshooting table lists parts and wiring referenced in the troubleshooting procedure.

Troubleshooting Procedure

Test the Y-Axis Motor.
Run the Service Diagnostics Y-Axis Motor
test.
Did the test pass?

Replace the Drum
Assembly (REP
2.0.3).

Replace the Y-Axis
Motor (REP 4.0.11).

Table 2 Y-Axis Sub-System Faults Troubleshooting Procedure

Step Questions or Actions

Yes

Y-Axis Sub-System Program Faults

5,001.63

Y-Axis sub-system general fault.

5,005.67

Sub-system not in homeless or idle state, software fault.

5,006.68

Software fault.

5,007.60

Software fault.

5,008.61

PostScript failed to fill the buffer.

5,009.62

Imaging errors. Possible jets On/Off outside the deadband area.

Table 1 5,0xx.6x Troubleshooting Reference Table

Applicable Parts

Wiring and Plug/Jack References

NVRAM, PL 5.0

Table 2 Y-Axis Sub-System Program Faults Troubleshooting Procedure

Step Questions or Actions

Yes

Reseat all Electronics Module connec-
tions.
Does the problem persist?

Go to Step 2.

Complete.

Check ground integrity.
Are the system grounds connected?

Reset NVRAM. If the
error persists,
replace the NVRAM
device (REP 5.0.9).

Reconnect the sys-
tem grounds.

Summary of Contents for PHASER 8560MFP









































































































































































































































































































Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands

Xerox PHASER 8560MFP, Service Documentation

Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands