Xerox PHASER 8560MFP Service Documentation Download Page 159

Page: 159 / 296

10/2006

4-45

Phaser 8510/8560MFP Multifunction Product

REP 4.0.3, REP 4.0.4

Repairs and Adjustments

Initial Issue

REP 4.0.3 Scanner Power Supply Fan

Parts List on PL 4.0

Removal

Remove the Scanner Assembly with attached DADF (REP 1.0.11).

Remove the Output Tray (REP 1.0.6).

Remove the Left Side Cover (REP 1.0.7).

Remove the Right Side Cover (REP 1.0.21).

Remove the Rear Cover (REP 1.0.20).

Disconnect the fan connector (CN5) from the Exit Module Control Board.

Remove 2 (plastic, T-20) screws that secure the fan to the frame.

Figure 1 Removing the Scanner Power Supply Fan

Replacement

NOTE: Route the fan harness behind the mylar insulator as shown in Figure 1.

REP 4.0.4 Head Maintenance Clutch

Parts List on PL 4.0

Removal

Remove the Scanner Assembly with attached DADF (REP 1.0.11).

Remove the Output Tray (REP 1.0.6).

Remove the Right Side Cover (REP 1.0.21).

Disconnect the Head Maintenance Clutch (P/J130) from the harness.

Remove the KL-Clip that secures the Wiper Clutch to the shaft and remove the clutch.

Figure 1 Removing the Head Maintenance Clutch

Replacement

Perform the Head Tilt Gear (ADJ 4.13.1), and Process Drive Alignment (ADJ 4.7.1) adjust-
ments before restoring system power.

Summary of Contents for PHASER 8560MFP









































































































































































































































































































Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands

Xerox PHASER 8560MFP, Service Documentation

Search results

Summary of Contents for PHASER 8560MFP

Reviews:

Related manuals for PHASER 8560MFP

Brands by name

Popular brands