WinGD X82-B Maintenance Manual Download Page 3

Page: 3 / 841

Table of contents

Maintenance Manual - change record. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3

Technical documentation set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4

Data module codes (procedural data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5

Data module codes (descriptive data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6

Data module codes (illustrated parts data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7

About this book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.8

About the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.9

List of abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety

2.1

Safety precautions and safety rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General data for maintenance

3.1

Lifting tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2

Jointing compounds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3

Clearances - general. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4

Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5

Torque values - standard screws. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General maintenance procedures

4.1

Do maintenance work - general procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2

Tighten a round nut with a pre-tensioner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3

Loosen a round nut with a pre-tensioner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4

Do a check of the pre-tension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance schedule

5.1

Maintenance schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Group 1 - Engine frame and bearings

6.1

Foundation bolts

6.1.1

Bedplate - do a check of the foundation bolts. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2

Main bearing - bearing shell number 1

6.2.1

Main bearing - bearing shell - No. 1 - prepare before removal. . . . . . . . . . . . . . .

6.2.2

Main bearing - bearing shell - No. 1 - remove. . . . . . . . . . . . . . . . . . . . . . . . . . . .

100

6.2.3

Main bearing shell - No.1 - do a check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

108

6.2.4

Main bearing - bearing shell - No. 1 - install. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

110

6.3

Main bearing - bearing shell number 2 to #

X82-B

Maintenance Manual

Winterthur Gas & Diesel Ltd.

- 3 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands