WinGD X82-B Maintenance Manual Download Page 426

Page: 426 / 841

Make sure that the holes in the bearing cover (005) engage with the four dowel pins
(009).

Remove the chain blocks (002, 006), chain (004), shackles (001, 003) and eye bolts.

Install the four round nuts (008) to the elastic bolts (007), refer to section

4.2 Tighten a

round nut with a pre-tensioner

X82-B

AA00-3303-01AAA-720A-A

Maintenance Manual

Connecting rod - install the top end bearing cover

Winterthur Gas & Diesel Ltd.

- 426 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands