manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 546

Fig 10-3

 Guide piston and roller removal

002

006

004

005

00423

007

008

001

010

009

003

011

2.2

Remove the guide piston (004) from the housing.

2.3

Remove the roller (008) together with the two pressure discs (008) and the bush
(007).

2.4

Remove and discard the O-ring (006).

2.5

Remove the snap ring (005).

2.6

Remove the Allen screws (011).

2.7

Remove the bottom housing (009) from top housing.

2.8

If necessary, replace the bush (010) as follows:

2.8.1

Remove the bush.

2.8.2

Apply Loctite No. 648 to the thread of the bush.

2.8.3

Torque the new bush to 200 Nm.

X82-B

AA00-5556-00AAA-530A-A

Maintenance Manual

Fuel pump - disassemble

Winterthur Gas & Diesel Ltd.

- 546 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands