manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 217

PROCEDURE

CAUTION

Make sure that you do not cause damage to the running surface of the cylinder liner
when you operate the grinding device.

1

Put applicable protection below the cylinder liner to keep particles out of the area.

2

Attach the grinding device (001) to the cylinder liner (002) (refer to the Manufacturer’s
Instruction Manual and 

Figure 7-7

).

3

Attach an applicable air supply to the grinding tool (001).

4

Use the grinding tool to carefully remove the unwanted edge (003) from the cylinder
liner (002).

5

Make sure that you get the radius r = 8 mm as shown.

6

Remove waste particles from the scavenge space.

7

Clean the cylinder liner bore.

Fig 7-7

 Cylinder liner - grind

CLOSE UP

•

None

X82-B

AA00-2124-00AAA-655A-A

Maintenance Manual

Cylinder liner - grind

Winterthur Gas & Diesel Ltd.

- 217 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands