WinGD X82-B Maintenance Manual Download Page 366

Page: 366 / 841

Fig 8-18

Stop plate

Lift the crosshead.

Remove the lever chain hoists (004,

Figure 8-17

) from the tool (009).

Remove the toggle lever (001) from the crosshead.

Put protection on the toggle lever (001) and the crosshead to prevent contamination and
damage.

CLOSE UP

•

None

X82-B

AA00-3303-00AAA-523A-A

Maintenance Manual

Connecting rod - prepare before removal

Winterthur Gas & Diesel Ltd.

- 366 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands