manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 599

PROCEDURE

1

Use a 

vacuum cleaner

 to remove dirt from all openings.

2

Clean the ICU.

3

Lubricate correctly the ICU.

4

Put the ICU in a 

plastic bag

.

5

Remove as much air as possible from the plastic bag.

6

Seal the plastic bag.

CLOSE UP

•

None

X82-B

AA00-5562-03AAA-810A-A

Maintenance Manual

Injection control unit - do the preservation

Winterthur Gas & Diesel Ltd.

- 599 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands