manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 732

13.3.4

HP fuel pipe (fuel pump to fuel rail) - remove

Periodicity

Description

Unscheduled
Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

1.5 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Basic

AR

Support equipment

Description

Part No.

CSN

QTY

None

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

WARNING

Injury Hazard. Always put on gloves and safety goggles when you do work on hot
components. When screws and plugs are opened, steam or fuel can come out and cause
injury.

CAUTION

Damage Hazard: Make sure that you do not damage the sealing faces or the HP fuel
pipes. Do not apply lateral force to the HP fuel pipes and the flanges.

CAUTION

Injury Hazard. The HP fuel pipes are heavy. Use only approved lifting equipment or
sufficient personnel to lift and move the HP fuel pipes.

PRELIMINARY OPERATIONS

•

The engine must be stopped and made safe for maintenance.

•

The fuel supply pump must be set to off.

X82-B

AA00-8752-01AAA-520A-A

Maintenance Manual

HP fuel pipe (fuel pump to fuel rail) - remove

Winterthur Gas & Diesel Ltd.

- 732 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands