manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 319

PROCEDURE

1

Clean the bores and the sealing faces of the valve cage (003, 

Figure 7-52

) and of the

valve seat (005).

2

Apply oil or Never-Seez NBST-8 to the bores and to the sealing faces of the valve cage
(003) and of the valve seat (005).

3

Apply the same lubricant to the new O-ring (004).

4

Put the new O-ring (004) on the valve seat (005).

5

If the valve seat (005) was removed to replace the O-ring (004), align the marks on the
valve seat (005) with the marks on the valve cage (003).

6

Put the valve seat (005) into the bore of the valve cage (003).

7

Install the top two halves of the valve seat tool (001) into the groove of the valve seat
(005).

8

Install the bottom two halves of the valve seat tool (001) into the groove of the valve
cage (003).

9

Turn equally the four jack-screws (002) to fully push the valve seat (005) into the valve
cage (003).

10

Use the feeler gauge to make sure that there is no clearance between the sealing faces.

11

Remove the valve seat tool (001).

Fig 7-52

 Valve seat - install

Sealing Faces

004

005

001

002

003

00730

CLOSE UP

•

Assemble the exhaust valve, refer to section 

7.7.8 Exhaust valve - assemble

X82-B

AA00-2751-01AAA-720A-A

Maintenance Manual

Exhaust valve - install the seat

Winterthur Gas & Diesel Ltd.

- 319 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands