manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 230

7.2.2

Lubricating quill - do a functional test

Periodicity

Description

Unscheduled

at each piston removal

Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

0.25 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Basic

1

Support equipment

Description

Part No.

CSN

QTY

HP oil pump

94931

1

Distributing piece

94934

1

Pressure gauge

94934A

1

Connection nipple

94934I

1

HP hose

94935

1

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

WARNING

Injury Hazard: Hydraulic tools can cause injury to personnel. Always put on gloves, a
face shield and safety goggles when you do work with hydraulic tools.

PRELIMINARY OPERATIONS

•

The lubricating quill must be removed, refer to section 

7.2.1 Lubricating quill - remove

•

During this procedure, use oil SAE50 at 40°C (approximately 200 cSt) or SAE30 at 25°C
(approximately 190 cSt).

•

During this procedure, contamination of the non-return valve with dirty or metal chips
must be prevented.

X82-B

AA00-2138-00AAA-340A-A

Maintenance Manual

Lubricating quill - do a functional test

Winterthur Gas & Diesel Ltd.

- 230 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands