WinGD X82-B Maintenance Manual Download Page 156

Page: 156 / 841

Attach the manual ratchet (003) to the lug (002) on the bearing cover.

Fig 6-24

Roller support

CAUTION

Damage Hazard: Use the roller support only as shown on its Warning plate. The
maximum permitted load is 16000 N at 45°.

Operate the manual ratchet (004,

Figure 6-25

) to lift the bearing cover (003).

Attach the eye bolt 94045-M56 (005) to the cylinder block.

Attach the shackle 94019K (007) to the lug (006) on the bearing cover (003).

Attach the chain block 94017-028 (005) to the eye bolt (001) and the shackle (007).

Apply tension to the chain block (005).

Remove the roller support (002) and the manual ratchet (004).

X82-B

AA00-1132-01AAB-520A-A

Maintenance Manual

Main bearing cover - No. 2 to # - remove

Winterthur Gas & Diesel Ltd.

- 156 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands