WinGD X82-B Maintenance Manual Download Page 671

Page: 671 / 841

Fig 11-25 Water separator - view 5

001

002

00449

Put the spur-geared chain block (001,

Figure 11-25

) into the middle hole of the lifting

tool.

Move the water separator until it hangs vertical to the spur-geared chain block (001).

13.1

Loosen or tighten the spur-geared chain block (001).

13.2

Loosen or tighten the spur-geared chain block (002).

Use the engine room crane to move the water separator to an applicable area.

CLOSE UP

•

None

X82-B

AA00-6708-00AAA-520A-A

Maintenance Manual

Water separator - remove

Winterthur Gas & Diesel Ltd.

- 671 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands