manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 526

9.2.3

Shut-off valve for starting air - do a test of the operation

Periodicity

Description

Working hours

18 000

Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

1.0 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Intermediate

AR

Support equipment

Description

Part No.

CSN

QTY

None

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

WARNING

Injury Hazard: During this test, do not select START. Injury to personnel can occur.

WARNING

Injury Hazard: Before you operate the turning gear, make sure that no personnel are near
the flywheel or in the engine.

PRELIMINARY OPERATIONS

•

The engine must be fully assembled and ready to start.

X82-B

AA00-4325-00AAA-320A-A

Maintenance Manual

Shut-off valve for starting air - do a test of the operation

Winterthur Gas & Diesel Ltd.

- 526 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands