WinGD X82-B Maintenance Manual Download Page 657

Page: 657 / 841

Prepare the expansion (front) side of the SAC for removal.

2.1

If applicable, remove the two rollers (002,

Figure 11-15

2.2

Remove the flange (003).

2.3

Remove and discard the O-ring (005).

2.4

Attach three swivel lugs (008).

2.5

Attach the left and the right support (011, 009) with the screws (012).

Fig 11-15 Scavenge air cooler (example) - prepare front side

001
002

003

III

004

005

006

003 007

III

004

002

004

008

009

010

011

012

X82-B

AA00-6606-00AAA-520A-A

Maintenance Manual

Scavenge air cooler - remove

Winterthur Gas & Diesel Ltd.

- 657 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands