manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 55

Fig 3-2

 RUD-swivel lugs

00285

Force

Direction

Force

Direction

Force

Direction

3.1.5

 Shackles

Only those shackles may be used which are in accordance with American Standard RR−C
−271A or which fulfil or exceed these values, including the safety factor.

All calculations for components and tools where shackles are used are laid out accordingly and
based on the mentioned standards.

Normally, the permissible lifting capacity of the shackles is specified for one single strand.

X82-B

AA00-0000-00AAA-066A-A

Maintenance Manual

Lifting tools

Winterthur Gas & Diesel Ltd.

- 55 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands