WinGD X82-B Maintenance Manual Download Page 440

Page: 440 / 841

63.5

Move the trolley (011) and crosshead pin (003) to an applicable area.

63.6

Lower the crosshead pin on an applicable surface.

63.7

Remove the chain block (008) from the lifting tool (007) on the crosshead (003).

X82-B

AA00-3326-00AAA-520A-A

Maintenance Manual

Crosshead - remove

Winterthur Gas & Diesel Ltd.

- 440 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands