WinGD X82-B Maintenance Manual Download Page 623

Page: 623 / 841

PROCEDURE

Remove the pan head screw (007,

Figure 10-40

Fig 10-40 Exhaust valve control unit - disassemble/assemble

001

002

003

004

005

006

FLUSH

007

008

009

010

00401

Remove the plug (008).

Remove and discard the O-ring (006) and the back-up ring (005).

Make sure that the piston (009) moves freely.

Remove the filter holder (002) and the screw plug (003) from the valve control block
(010).

Make sure that the oil filter (001) is clean and has no damage. If necessary, remove and
discard the oil filter.

Make sure that the seal (004) has no damage. If necessary, remove and discard the
seal.

CLOSE UP

•

None

X82-B

AA00-5612-00AAA-530A-A

Maintenance Manual

Exhaust valve control unit (VCU) - disassemble

Winterthur Gas & Diesel Ltd.

- 623 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands