manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 113

Fig 6-5

 Bearing shell - lift

003

00608

002

001

002

003

1.9

Remove carefully the engine room crane from the lifting tool (002).

1.10

Operate carefully the chain block (001) to lower the bearing shell (003) on to the
crankshaft.

X82-B

AA00-1132-00AAA-720A-A

Maintenance Manual

Main bearing - bearing shell - No. 1 - install

Winterthur Gas & Diesel Ltd.

- 113 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands